Tcl8.6.13/Tk8.6.13 Documentation > Tcl Commands > memory

Tcl/Tk Applications | Tcl Commands | Tk Commands | [incr Tcl] Package Commands | SQLite3 Package Commands | TDBC Package Commands | tdbc::mysql Package Commands | tdbc::odbc Package Commands | tdbc::postgres Package Commands | tdbc::sqlite3 Package Commands | Thread Package Commands | Tcl C API | Tk C API | [incr Tcl] Package C API | TDBC Package C API

NAME
memory — Control Tcl memory debugging capabilities
SYNOPSIS
DESCRIPTION
memory active file
memory break_on_malloc count
memory info
memory init [on|off]
memory objs file
memory onexit file
memory tag string
memory trace [on|off]
memory trace_on_at_malloc count
memory validate [on|off]
SEE ALSO
KEYWORDS

NAME

memory — Control Tcl memory debugging capabilities

SYNOPSIS

memory option ?arg arg ...?

DESCRIPTION

The memory command gives the Tcl developer control of Tcl's memory debugging capabilities. The memory command has several suboptions, which are described below. It is only available when Tcl has been compiled with memory debugging enabled (when TCL_MEM_DEBUG is defined at compile time), and after Tcl_InitMemory has been called.

memory active file
Write a list of all currently allocated memory to the specified file.

memory break_on_malloc count
After the count allocations have been performed, ckalloc outputs a message to this effect and that it is now attempting to enter the C debugger. Tcl will then issue a SIGINT signal against itself. If you are running Tcl under a C debugger, it should then enter the debugger command mode.

memory info
Returns a report containing the total allocations and frees since Tcl began, the current packets allocated (the current number of calls to ckalloc not met by a corresponding call to ckfree), the current bytes allocated, and the maximum number of packets and bytes allocated.

memory init [on|off]
Turn on or off the pre-initialization of all allocated memory with bogus bytes. Useful for detecting the use of uninitialized values.

memory objs file
Causes a list of all allocated Tcl_Obj values to be written to the specified file immediately, together with where they were allocated. Useful for checking for leaks of values.

memory onexit file
Causes a list of all allocated memory to be written to the specified file during the finalization of Tcl's memory subsystem. Useful for checking that memory is properly cleaned up during process exit.

memory tag string
Each packet of memory allocated by ckalloc can have associated with it a string-valued tag. In the lists of allocated memory generated by memory active and memory onexit, the tag for each packet is printed along with other information about the packet. The memory tag command sets the tag value for subsequent calls to ckalloc to be string.

memory trace [on|off]
Turns memory tracing on or off. When memory tracing is on, every call to ckalloc causes a line of trace information to be written to stderr, consisting of the word ckalloc, followed by the address returned, the amount of memory allocated, and the C filename and line number of the code performing the allocation. For example:

ckalloc 40e478 98 tclProc.c 1406

Calls to ckfree are traced in the same manner.

memory trace_on_at_malloc count
Enable memory tracing after count ckallocs have been performed. For example, if you enter memory trace_on_at_malloc 100, after the 100th call to ckalloc, memory trace information will begin being displayed for all allocations and frees. Since there can be a lot of memory activity before a problem occurs, judicious use of this option can reduce the slowdown caused by tracing (and the amount of trace information produced), if you can identify a number of allocations that occur before the problem sets in. The current number of memory allocations that have occurred since Tcl started is printed on a guard zone failure.

memory validate [on|off]
Turns memory validation on or off. When memory validation is enabled, on every call to ckalloc or ckfree, the guard zones are checked for every piece of memory currently in existence that was allocated by ckalloc. This has a large performance impact and should only be used when overwrite problems are strongly suspected. The advantage of enabling memory validation is that a guard zone overwrite can be detected on the first call to ckalloc or ckfree after the overwrite occurred, rather than when the specific memory with the overwritten guard zone(s) is freed, which may occur long after the overwrite occurred.

SEE ALSO

ckalloc, ckfree, Tcl_ValidateAllMemory, Tcl_DumpActiveMemory, TCL_MEM_DEBUG

KEYWORDS

memory, debug
Copyright © 1992-1999 Karl Lehenbauer & Mark Diekhans
Copyright © 2000 Scriptics Corporation.